Heat Exchanger Se134 Lab Report Uitm

10Introduction The heat exchanger is a device in which as the name refers exchange of heat occurs between two fluids gases or liquids that come in and leave at varied temperature levels. Studies Thermodynamics Organic Chemistry and Inorganic Chemistry.

Level Process Control Se665 Manualnew Solteq Level Flow Process Control Training System Model Se 665 1 0 Introduction The Level Flow Process Control Course Hero

The purpose of this paper is how to design the shell and tube heat exchanger which is the majority type of liquid to- liquid heat exchanger.

Heat exchanger se134 lab report uitm. And calculated given the heat-exchanger effectiveness the mass-flow rates and specific heats of the two fluids and the inlet temperatures. The Heat Exchanger Inspection article provides you with information about the inspection of the heat exchanger and heat exchanger testing during the manufacturing phase as well as in-service inspection in operating units. The following sections are to be included in this order.

Heat exchanger lab 2. Kebakaran di Kolej Jati Uitm Shah Alam Sep 2011 4 Jan 2011 1 2010 7 Sep 2010 5 Aug 2010 2 Komen dan pendapat. The value of depends on the heat-exchanger geometry and flow pattern parallel flow counterflow cross flow etc.

The H102C Shell and tube exchanger is a simple model that demonstrates the basic principles of heat transfer. The HE 165 which demonstrates the heat pump application which there are the presences of large freely energy source. One common example of a heat exchanger is the radiator in a car in which the heat source being a hot engine-cooling fluid water transfers heat to air flowing through the radiator ie.

Your lab report is to include the following. Use double spacing with 12 fonts. 3 Please cancel which is not No.

Write a summary max. If all these elements are interconnected. Calculations on the heat transfer and heat loss were carried out for energy balance study.

From the data collected we found out that configuration of Shell and Tube heat exchanger in. Figure 4 shows a schematic diagram of cross-flow heat exchanger. SOLTEQ HEAT EXCHANGER PROCESS CONTROL TRAINING SYSTEM MODEL.

The process in solving simulation consists of modeling and meshing the basic geometry of shell and tube heat exchanger using CFD package ANSYS 130. You may want to review shell and tube heat exchanger inspection procedure and related inspection and test plan. The miniature heat exchanger is mounted on the H102 front panel that incorporates two mounting studs.

The student will also learn about the different transducers used to detect and measure the physical properties used when calculating the heat transfer between the hot and cold media in the heat exchanger. A HT30XC Heat Exchanger Unit and HT31 Tubular tube-in-tube Heat Exchanger are used for this laboratory. Supply all plots taken for this lab make sure they are labelled properly.

Nurlina Syahiirah Universiti Teknologi Mara Chemical Engineering Department Undergraduate. Get widget here. The device used to implement this exchange is termed a heat.

Check Pages 1 - 4 of Refrigeration Lab Report2037 in the flip PDF version. The H102C is designed for use with the Heat Exchanger Service Unit H102. To provide the appropriate output the valve travels between fully.

Heat Exchanger Demonstration Lab Summary The process of heat exchange between two fluids that are at different temperatures and sepa-rated by a solid wall occurs in many engineering applications. The engine oil at a flow rate of 023 kgs enters the exchanger at 120C and leaves at 115C. Cross flow heat exchanger In a cross-flow heat exchanger the paths of the two fluid streams through the heat exchanger are usually at right angles to each other.

Theoretical relations for and graphical characteristics are given by Ozisik 1 and Incropera DeWitt 2 for a limited selection of. Heat exchanger design report design of a shell and tube heat exchanger 1 shell -1 tube pass with fixed tube head and counter current flow statement. Find more similar flip PDFs like Refrigeration Lab Report2037.

In the shower as in most process control systems the final control element is a valve which partially opens or closes to regulate the mass or energy inflow. 500 words in a text box if using Excel comparing your results and suggestions for further study. The cross flow heat exchanger in our laboratory is of finned type and the cooling media used is air.

Lab Report SOLTEQ Concentric Tube Heat Exchanger Unit HE104-PD Page 6 For a double pipe heat exchanger the overall heat transfer coefficient U can be expressed as. SE134 established a proportion of hot water to cold which can be maintained continuously. Use A4 paper for the entire report.

4 INTRODUCTION For the refrigerant unit experiment the Mechanical Heat Pump serve as the purpose to study about vapour compression cycle. Unit Operations Lab Heat Exchanger 1-6 Ý L M M k _ v 14 where q is the actual rate of heat transfer from the hot to cold fluid and qmax is the maximum possible rate of heat transfer for given inlet temperatures of the fluids M k _ v L k g l. HEAT EXCHANGER Mark.

SE134 30 THEORETICAL BACKGROUND 31 Process Control A fundamental component of any industrial process control system is the feedback control loop. Download Refrigeration Lab Report2037 PDF for free. 15 Here Cmin is the smaller of the two heat capacity rates Cc and ChIf heat exchanger effectiveness.

Spelling and usage should be conventionally correct. Guidelines for Preparation of Laboratory Reports The report should be typewritten with the graphs by a computer. Where Area Surface area of contact pi x O Dinner pipe x Length 3142 x 0015 x 136 m² 00641 m² The only part of the overall heat transfer coefficient that needs.

Use MATLAB or MS Excel and calculate the LMTD and Heat Exchanger effectiveness values for the 3 tests. LMTD and heat transfer coefficient also calculated for this experiment. The 50 ethylene glycol at a rate of 047 kgs enters at 90C.

FACULTY OF CHEMICAL ENGINEERING Universiti Teknologi MARA UiTM Terengganu Kampus Bukit Besi 23200 Dungun TERENGGANU TECHNICALEXECUTIVE REPORT. SOLTEQ HEAT EXCHANGER PROCESS CONTROL TRAINING SYSTEM MODEL. Smaller heat exchanger for the same capacity.

Heat transfer area and pressure drops and checking whether the assumed design satisfies all requirement or not. HE 165 is capable to expose student with a practical and proper demonstration on vapour compression cycle. The Mechanical Heat Pump Model.

CHEMICAL ENGINEERING Lab No. Refrigeration Lab Report2037 was published by redahoussaini on 2019-11-02. 3 MEI 2018 Participant Course.

The heat transfer mediumThe main purpose of heat exchanger is to remove the heat from the hot fluid and transfer it into the cold fluid. Example 52 Miniature Shell-and-Tube Heat Exchanger A miniature shell-and-tube heat exchanger is designed to cool engine oil in an engine with the engine coolant 50 ethylene glycol. Abstract The objective of this experiment is to study the function and the working of shell and tube heat exchanger.

The core objective of the equipment in an industrial set-up is to achieve a suitable temperature of a fluid by adding or removing. In present day shell and tube heat exchanger is the most common type heat exchanger widely use in oil refinery and other large chemical process because it suits high pressure application. 6 Ü F 6 Ü.

I believe good knowledge should be free and as long as you have the effort the gain. It consists of the process the measurement the controller and the final control element as shown in figure 1. A characteristic of heat exchanger design is the procedure of specifying a design.

Level Process Control Se665 Manualnew Solteq Level Flow Process Control Training System Model Se 665 1 0 Introduction The Level Flow Process Control Course Hero

Level Process Control Docx Faculty Of Applied Sciences Diploma In Industrial Chemistry As115 Process Instrumentation Laboratory Report Cmt 350 Title Course Hero